Dispersion adhesive for textile floor coverings
| Purpose | Dispersion adhesive for textile floor coverings |
|---|---|
| Surface | The substrate must be solid, flat, dry, uncracked, clean and free of stains that impair adhesion. Inspect the substrate according to applicable standards and technical sheets and immediately point out any irregularities. Vacuum the substrate thoroughly, then treat it with primer and leveling compound. Suitable primers and leveling compounds are listed in the UZIN product table. When choosing, take into account the type of base, the type of floor covering and the level of load. Non-absorbent substrates or substrates sensitive to moisture, such as e.g. apply a leveling layer of at least 2 mm on new cast asphalt screeds, at least 1-2 mm of leveling layer on new anhydrite screeds and at least 2 mm of leveling layer on old substrates. The base and leveling layer should dry well. Also refer to the data sheets for all other products used. |
| Suitable for (space) | textile floor coverings with a secondary backing textile floor coverings with a foam, latex, felt, textile or jute backing needle felt floor coverings natural fiber floor coverings on absorbent pre-levelled sub-floors residential and commercial floors floors with underfloor heating roller chair loads according to DIN 12 529 suitable for mechanical cleaning of floor coverings |
| Suitable for | textile floor coverings with a secondary backing textile floor coverings with a foam, latex, felt, textile or jute backing needle felt floor coverings natural fiber floor coverings on absorbent pre-levelled sub-floors residential and commercial floors floors with underfloor heating roller chair loads according to DIN 12 529 suitable for mechanical cleaning of floor coverings |
| Surface preparation | The substrate must be solid, flat, dry, uncracked, clean and free of stains that impair adhesion. Inspect the substrate according to applicable standards and technical sheets and immediately point out any irregularities. Vacuum the substrate thoroughly, then treat it with primer and leveling compound. Suitable primers and leveling compounds are listed in the UZIN product table. When choosing, take into account the type of base, the type of floor covering and the level of load. Non-absorbent substrates or substrates sensitive to moisture, such as e.g. apply a leveling layer of at least 2 mm on new cast asphalt screeds, at least 1-2 mm of leveling layer on new anhydrite screeds and at least 2 mm of leveling layer on old substrates. The base and leveling layer should dry well. Also refer to the data sheets for all other products used. |
| Processing | 1. Mix the adhesive well before use and apply it evenly to the substrate with a suitable spatula. 2. Apply only as much glue as you can in the given time of airing and laying the lining, which will form adequate adhesive threads over the entire surface of the back. 3. Place the covering carefully and press it thoroughly over the entire surface onto the substrate. 4. After about 20 minutes, press again and roll with a suitable roller, especially the joints and uneven parts. Repeat the procedure if necessary. 1. Mix the adhesive well before use and apply it evenly to the substrate with a suitable spatula. 2. Apply only as much glue as you can in the given time of airing and laying the lining, which will form adequate adhesive threads over the entire surface of the back. 3. Place the covering carefully and press it thoroughly over the entire surface onto the substrate. 4. After about 20 minutes, press again and roll with a suitable roller, especially the joints and uneven parts. Repeat the process if necessary. |
| Effect | simple and easy to use good formation of adhesive threads good adhesion optimal initial and final strength neutral odor for indoor spaces |
| Usage | The product can be stored for at least 12 months in the original closed packaging in a moderately cool place. The product must not freeze. Close the opened packaging tightly after use and use the product as soon as possible. The product should reach room temperature before use. Ideal working conditions are: temperature between 18 and 25 °C, soil temperature above 15 °C and relative air humidity below 65%. At lower temperatures and higher air humidity, the drying time is longer, and at higher temperatures and lower air humidity, it is shortened. Before gluing, the floor covering must be spread out in order to relax and adapt to the room climate that will prevail during subsequent use. Use water to remove fresh glue stains and to clean work tools immediately after work. The following standards, directives and technical sheets also apply or are specifically recommended: - DIN 18365: "Laying floor coverings" - technical sheet of the Industrial Association for Adhesives "Assessment and preparation of the base - gluing elastic and textile floor coverings" - technical sheet of the Central Association of the German Building Industry (ZDB) "Elastic floor coverings, textile floor coverings and parquet on heated floor structures" - TKB technical sheet "Assessment and preparation of the base for floor coverings and parquet works" - BEB technical sheet "Assessment and preparation of the base" - TKB technical sheet "Gluing PVC floor coverings" - TKB technical sheet "Gluing elastic floor coverings" The product can be stored for at least 12 months in the original closed packaging in a moderately cool place. The product must not freeze. Close the opened packaging tightly after use and use the product as soon as possible. The product should reach room temperature before use. Ideal working conditions are: temperature between 18 and 25 °C, soil temperature above 15 °C and relative air humidity below 65%. At lower temperatures and higher air humidity, the drying time is longer, and at higher temperatures and lower air humidity, it is shortened. Before gluing, the floor covering must be spread out in order to relax and adapt to the room climate that will prevail during subsequent use. Use water to remove fresh glue stains and to clean work tools immediately after work. The following standards, directives and technical sheets also apply or are specifically recommended: - DIN 18365: "Laying floor coverings" - technical sheet of the Industrial Association for Adhesives "Assessment and preparation of the base - gluing elastic and textile floor coverings" - technical sheet of the Central Association of the German Building Industry (ZDB) "Elastic floor coverings, textile floor coverings and parquet on heated floor structures" - TKB technical sheet "Assessment and preparation of the base for floor coverings and parquet works" - BEB technical sheet "Assessment and preparation of the base" - TKB technical sheet "Gluing PVC floor coverings" - TKB technical sheet "Gluing elastic floor coverings" |
| Additional specification | Universal dispersion adhesive with the addition of artificial resins for gluing all types of textile floor coverings. Universal, economical and easy to use. Optimum adhesive strength and excellent formation of adhesive threads enable additional reliability in use. |
| Packaging | 8 kg, 26 kg |
Documents for this product are being prepared. Contact us if you need them now.
Recently viewed
UZIN KE 570